csm_xw2b_ds_e_3_1 1 standard-type connector-terminal block conversion units xw2b simplifies connector and terminal block replacement, and requires less in-panel wiring. ? mount to din track or via screws. ? mil flat cable connectors and multi-pole, square connectors are standard. ? terminal blocks available with either m3 or m3.5 screws. ? connecting cables for pr ogrammable controllers available (sold se parately). ordering information connectors *1. flat cable connectors have one polarity slot. *2. these plugs and sockets are made by honda tsushin kogyo. *3. these plugs are made by fujitsu. accessories (order separately) connecting cables for connector-terminal block conversion units for details on the connecting cable used between xw2b daisy chain-type connectors, refer to the xw2z datasheet . type terminal block connector no. of poles appearance model flat cable terminal block with m3 screws flat cable connectors *1 20 xw2b-20g4 34 XW2B-34G4 40 xw2b-40g4 50 xw2b-50g4 60 xw2b-60g4 terminal block with m3.5 screws 20 xw2b-20g5 34 xw2b-34g5 40 xw2b-40g5 50 xw2b-50g5 60 xw2b-60g5 twin-connector terminal block with m3.5 screws 40 xw2b-40g5-t daisy chain 20 xw2b-20g5-d multi-pole, square connector terminal block with m3 screws multi-pole, square connector plugs *2 20 xw2b-20y4 34 xw2b-34y4 50 xw2b-50y4 terminal block with m3.5 screws 20 xw2b-20y5 34 xw2b-34y5 50 xw2b-50y5 multi-pole, square connector plugs *2 20 xw2b-20x5 34 xw2b-34x5 50 xw2b-50x5 board i/o terminal block with m3.5 screws multi-pole, square connector plugs *3 40 xw2b-40f5-p
xw2b 2 ratings and specifications dimensions (unit: mm) flat cable units with a terminal block with m3 screws applicable connectors *1. either the xg5m- @@ 32-n or the xg5m- @@ 35-n may be used. *2. each connector requires two semi-covers. type item xw2b- @ @ g @ flat cable units xw2b- @ @ y @ multi-pole, square-connector units xw2b-40f5-p board i/o unit rated current 1 a rated voltage 125 vac insulation resistance 100 m ? min. (at 500 vdc) dielectric strength 500 vac for 1 min (leakage current: 1 ma max.) ambient operating temperature 0 to 55 c model applicable conne ctors (order separately) flat cable connec tors, mil sockets with strain reliefs discrete-wire idc connecto rs, double-row sockets connectors *1 semi-covers *2 xw2b-20g4 xg4m-2030-t xg5m-2032-n xg5m-2035-n xg5s-1001 XW2B-34G4 xg4m-3430-t xg5m-3432-n xg5m-3435-n xg5s-1701 xw2b-40g4 xg4m-4030-t xg5m-4032-n xg5m-4035-n xg5s-2001 xw2b-50g4 xg4m-5030-t xg5m-5032-n xg5m-5035-n xg5s-2501 xw2b-60g4 xg4m-6030-t xg5m-6032-n xg5m-6035-n xg5s-3001 flat cable connector (mating side) terminal block (terminal side) n 4 2 3 1 3 1 4 n-3 n-2 n-1 n 2 n-2 n-1 n-3 triangular mark flat cable connector (mil plug) 3.5 15.5 45 tw o, 3.5 dia. terminal block a 3.5 29.5 5.08 20.5 din track lock 38.1 (45.3) xw2b- @ @ g4 wiring diagram dimensions *flat cable connectors have one polarity slot. note: terminal block pitch is 5.08 mm. use a wire size between 0.3 and 1.25 mm 2 (awg22 to awg16). the wire insertion holes are 1.8 2.5 (h w) mm. model no. of poles dimension a (mm) applicable connector models *1 xw2b-20g4 20 67.5 xg4a-2031 XW2B-34G4 34 112.5 xg4a-3431 xw2b-40g4 40 135.0 xg4a-4031 xw2b-50g4 50 157.5 xg4a-5031 xw2b-60g4 60 180.0 xg4a-6031 note: all pins on the flat cable connector correspond 1-to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 3 flat cable units with a terminal block with m3.5 screws applicable connectors *1. either the xg5m- @@ 32-n or the xg5m -@@ 35-n may be used. *2. each connector requires two semi-covers. model applicable conne ctors (order separately) flat cable connec tors, mil sockets with strain reliefs discrete-wire idc connecto rs, double-row sockets connectors *1 semi-covers *2 xw2b-20g5 xg4m-2030-t xg5m-2032-n xg5m-2035-n xg5s-1001 xw2b-34g5 xg4m-3430-t xg5m-3432-n xg5m-3435-n xg5s-1701 xw2b-40g5 xg4m-4030-t xg5m-4032-n xg5m-4035-n xg5s-2001 xw2b-50g5 xg4m-5030-t xg5m-5032-n xg5m-5035-n xg5s-2501 xw2b-60g5 xg4m-6030-t xg5m-6032-n xg5m-6035-n xg5s-3001 flat cable connector (mil plug) 3.5 15.5 45 tw o, 3.5 dia. 7 terminal block 7.3 8.5 7 29.5 3.5 (45.3) 43.5 20.5 din track lock triangular mark flat cable connector (mating side) terminal block (terminal side) n 4 2 3 1 3 1 4 n-3 n-2 n-1 n 2 n-2 n-1 n-3 xw2b- @ @ g5 wiring diagram dimensions *flat cable connectors have one polarity slot. note: terminal block pitch is 8.5 mm. model no. of poles dimension a (mm) applicable connector models * xw2b-20g5 20 112.5 xg4a-2031 xw2b-34g5 34 180.0 xg4a-3431 xw2b-40g5 40 202.5 xg4a-4031 xw2b-50g5 50 247.5 xg4a-5031 xw2b-60g5 60 292.5 xg4a-6031 note: all pins on the flat cable connector correspond 1-to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 4 twin-connector units with a terminal block with m3.5 screws applicable connectors *1. either the xg5m- @@ 32-n or the xg5m- @@ 35-n may be used. *2. each connector requires two semi-covers. model applicable conne ctors (order separately) flat cable connec tors, mil sockets with strain reliefs discrete-wire idc connecto rs, double-row sockets connectors *1 semi-covers *2 xw2b-40g5-t xg4m-2030-t xg5m-2032-n xg5m-2035-n xg5s-1001 flat cable connector (mil plug: xg4a-2031 2) 3.5 15.5 45 tw o, 3.5 dia. 7 terminal block 7.3 8.5 7 29.5 3.5 din track lock 2 20.5 43.8 (45.3) 202.5 triangular mark triangular mark flat cable connector (mating side) terminal block (terminal side) 40 22 20 21 19 4 2 3 1 21 22 19 20 1 2 3 4 37 38 39 40 38 39 37 xw2b-40g5-t wiring diagram note: all pins on the flat cable connector correspond 1-to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 5 daisy chain units with a termin al block with m3.5 screws applicable connectors *1. either the xg5m- @@ 32-n or the xg5m- @@ 35-n may be used. *2. each connector requires two semi-covers. model applicable conne ctors (order separately) flat cable connec tors, mil sockets with strain reliefs discrete-wire idc connecto rs, double-row sockets connectors *1 semi-covers *2 xw2b-20g5-d xg4m-2030-t xg5m-2032-n xg5m-2035-n xg5s-1001 flat cable connector (mil plug: xg4a-2031 2) 3.5 135 3.5 29.5 7 8.5 7.3 terminal block 7 45 15.5 tw o, 3.5 dia. (45.3) 43.8 20.5 2 din track lock triangular mark triangular mark flat cable connector (mating side) terminal block (terminal side) 20 2 1 1 19 20 2 19 1 19 20 2 xw2b-20g5-d wiring diagram note: all pins on the flat cable connector correspond 1-to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 6 multi-pole, square-co nnector plug units with a t erminal block with m3 screws applicable connectors *1. all applicable connector hoods are made by honda tsushin kogyo. *2. use mrp-f113 or mrp-f103 crimp terminals made by honda tsushin kogyo. model applicable connectors *1 hood *1 xw2b-20y4 mr-20f (soldered) mrp-20f01 (crimped) *2 mr-20fw (wrapped) mr-20l xw2b-34y4 mr-34f (soldered) mrp-34f01 (crimped) *2 mr-34fw (wrapped) mr-34l xw2b-50y4 mr-50f (soldered) mrp-50f01 (crimped) *2 mr-50fw (wrapped) mr-50l multi-contact, square connector (mating side) terminal block (terminal side) 50 4 2 3 1 18 16 19 17 34 33 2 19 35 3 1 49 48 17 32 50 18 16 48 49 47 multi-contact connector (plug) 3.5 45 15.5 tw o, 3.5 dia. terminal block a 3.5 29.5 din track lock 2 20.5 38.1 5.08 xw2b- @ @ y4 wiring diagram (example for terminal block with 50 poles) dimensions *these connectors are made by honda tsushin kogyo. note: terminal block pitch is 5.08 mm. use a wire size between 0.3 and 1.25 mm 2 (awg22 to awg16). the wire insertion holes are 1.8 2.5 (h w) mm. model no. of poles dimension a (mm) applicable connector models * xw2b-20y4 20 67.5 mr-20rmd2 xw2b-34y4 34 112.5 mr-34rmd2 xw2b-50y4 50 157.5 mr-50rmd2 note: all pins on the multi-pole, square connector correspond 1-to- 1 to the terminal of the same number on the terminal block as shown above.
xw2b 7 multi-pole, square-co nnector plug units with a t erminal block wi th m3.5 screws applicable connectors *1. all applicable connector hoods are made by honda tsushin kogyo. *2. use mrp-f113 or mrp-f103 crimp terminals made by honda tsushin kogyo. model applicable connectors *1 hood *1 xw2b-20y5 mr-20f (soldered) mrp-20f01 (crimped) *2 mr-20fw (wrapped) mr-20l xw2b-34y5 mr-34f (soldered) mrp-34f01 (crimped) *2 mr-34fw (wrapped) mr-34l xw2b-50y5 mr-50f (soldered) mrp-50f01 (crimped) *2 mr-50fw (wrapped) mr-50l multi-contact, square connector (mating side) terminal block (terminal side) 50 4 2 3 1 18 16 19 17 34 33 2 19 35 3 1 49 48 17 32 50 18 16 48 49 47 3.5 29.5 multi-contact, square connector (plug) a 3.5 15.5 45 tw o, 3.5 dia. 43.8 20.5 2 din track lock 8.5 7.3 terminal block xw2b- @ @ y5 wiring diagram (example for terminal block with 50 poles) dimensions *these connectors are made by honda tsushin kogyo. note: terminal block pitch is 8.5 mm. model no. of poles dimension a (mm) applicable connector models * xw2b-20y5 20 112.5 mr-20rmd2 xw2b-34y5 34 180.0 mr-34rmd2 xw2b-50y5 50 247.5 mr-50rmd2 note: all pins on the multi-pole, square connector correspond 1-to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 8 multi-pole, square connector socket units with a terminal block with m3.5 screws applicable connectors *1. all applicable connector hoods are made by honda tsushin kogyo. *2. use mrp-f113 or mrp-f103 crimp terminals made by honda tsushin kogyo. model applicable connectors *1 hood *1 xw2b-20x5 mr-20m (soldered) mrp-20m01 (crimped) *2 mr-20mw (wrapped) mr-20l xw2b-34x5 mr-34m (soldered) mrp-34m01 (crimped) *2 mr-34mw (wrapped) mr-34l xw2b-50x5 mr-50m (soldered) mrp-50m01 (crimped) *2 mr-50mw (wrapped) mr-50l multi-contact, square connector (mating side) terminal block (terminal side) 50 4 2 3 1 18 16 19 17 2 1 34 19 3 35 33 17 16 49 32 18 50 48 48 49 47 3.5 29.5 8.5 7.3 terminal block tw o, 3.5 dia. 45 15.5 3.5 multi-contact, square connector (socket) a din track lock 2 20.5 43.8 xw2b- @ @ x5 wiring diagram (example for terminal block with 50 poles) dimensions *these connectors are made by honda tsushin kogyo. note: terminal block pitch is 8.5 mm. model no. of poles dimension a (mm) applicable connector models * xw2b-20x5 20 112.5 mr-20rfd2 xw2b-34x5 34 180.0 mr-34rfd2 xw2b-50x5 50 247.5 mr-50rfd2 note: all pins on the multi-pole, square connector correspond 1- to-1 to the terminal of the same number on the terminal block as shown above.
xw2b 9 board i/o units with a te rminal block with m3.5 screws applicable connectors *1. all applicable connectors and covers are made by fujitsu. *2. refer to the omnuc u series user's manual for details on the connecting cable used between the xw2b-40f5-p and the u-series ac servo driver. model applicable connectors *1 hood *1 xw2b-40f5-p fcn361j040-au (soldered) fcn363j040-aau (crimped) fcn360c040- b fcn-364p040-au plug (mating side) terminal block (terminal side) 20 19 20 19 39 37 40 38 2 1 2 1 3 1 4 2 b a i/o board connectors (40-pin plug) 202.5 m2.6 3.5 29.5 7 8.5 7.3 terminal block 7 45 15.5 tw o, 3.5 dia. 3.5 2 20.5 43.8 din track lock xw2b-40f5-p wiring diagram dimensions *these connectors and circuits are made by fujitsu. note: terminal block pitch is 8.5 mm. model no. of poles applicable connectors and circuits * xw2b-40f5-p 40 fcn-364p40-au (connector) fcn-360a1 (anchor)
xw2b 10 safety precautions wiring ? always turn off the power suppl y before wiring. otherwise, cables or other conductors can short the terminals and cause the unit to fail. ? do not connect or disconnect connectors with the power turned on. otherwise, it may cause malfunctions. wiring terminal blocks ? direct wire connections with a terminal block with m3 screws 1. use a wire size between 0.3 and 1.25 mm 2 (awg22 to awg16). 2. prepare the end of each wire as shown in the following diagram. 3. the wire insertion holes are 1.8 2.5 (h w) mm on the terminal block with m3 screws. ? direct wire connections with a terminal block with m3.5 screws (with a terminal block with m3 screws) note: round rod and blade crimp terminals are made by nichifu. terminal screw tightening torque ? select a tightening torque from the following table when connecting wires or crimp termi nals to the terminal block. mounting units to and removing units from din track ? for terminal blocks with m3 screws, use a flat-heat screwdriver like the one shown in the following diagram. ? xw2b connector-terminal block conversion units can be mounted side-to-side on din track. the flanges for mounting screws are located on each side at the bottom of the xw2b. ? secure both ends of the xw2b with end plates. ? when removing the unit from a din track, insert a flat-head screwdriver into the slider and pull the lock out. precautions for correct use applicable crimp terminals applicable wires round 1.25-3.5 awg22 to awg16 (0.30 to 1.25 mm 2 ) 2-3.5 awg16 to awg14 (1.25 to 2.0 mm 2) forked 1.25y-3.5 awg22 to awg16 (0.30 to 1.25 mm 2 ) 2y-3.5 awg16 to awg14 (1.25 to 2.0 mm 2 ) applicable crimp terminals applicable wires rod tc-05 dia. = 1 awg22 to awg18 (0.30 to 0.75 mm 2 ) tc-1.25s dia. = 1.5 awg22 to awg16 (0.30 to 1.25 mm 2 ) blade bt1.25-9-1 bt1.25-10-1 w = 2.2 awg22 to awg16 (0.30 to 1.25 mm 2 ) 6 mm 6.8 mm max. 3.7 mm dia. 6.8 mm max. 3.7 mm round forked dia. t = 0.75 w round rod blade terminal block tightening torque n ? m with m3 screws 0.40 with m3.5 screws 0.59 2.9- to 3.5-mm blade screw slot width: 0.7
|
